saw bandpass filter F1G56 features z gps applications z usable bandwidth of 2 mhz z no impedance matching require for operation at 50 ? z smd package 2.0 mm 1.6 mm 0.7 mm z single-ended operation z rohs compliant package dimensions 4 3 2 1 4 3 2 1 l q part no. F1G56 rev. date 2007-07-13 i t f co., ltd. 102-901, bucheon technopark 364, samjeong-dong, ojeong-gu, bucheon-city, gyounggi-do, korea 421-809 rev. nc7001-as02 1/7 pin configurations 1 input 2 case ground 3 output 4 case ground maximum ratings parameters unit minimum typical maximum operating temperature range -40 25 85 storage temperature range -40 - 95 power handling capability dbm - - 10 electrostatics sensitive device ( esd)
saw bandpass filter F1G56 specifications minimum typical maximum unit center frequency ( fc ) - 1575.42 - mhz insertion loss (fo +/- 1 mhz) - 1.1 1.6 db amplitude ripple (fo +/- 1 mhz) - 0.1 0.8 dbp-p vswr (fo +/- 1 mhz) - 1.2 1.8 relative attenuation d.c. ~ 1400 mhz 20.0 23.0 - 1400 ~ 1490 mhz 25.0 30.0 - db 1490 ~ 1520 mhz 30.0 35.0 - ( 1500 mhz ) (35.0) (44.0) - 1625 ~ 1635 mhz 30.0 42.0 - 1800 ~ 3000 mhz 25.0 30.0 - temperature range (operational) -40 25 85 input rf power (fo +/- 1 mhz) 10 dbm input/output impedance 50 ohms notes : 1) all specifications are based on th e matching schematic shown below, measur ed by agilent network analyzer and full 2 port calibration. 2) electrical margin has been built into the design to accoun t for the variations due to temperature drift and manufacturing tolerances 3) all attenuation measurements are measured relative to insertion loss part no. F1G56 rev. date 2007-07-13 i t f co., ltd. 102-901, bucheon technopark 364, samjeong-dong, ojeong-gu, bucheon-city, gyounggi-do, korea 421-809 rev. nc7001-as02 2/7
saw bandpass filter F1G56 matching schematic ( actual matching values may vary due to pcb layout and parasitics ) input 50 output 50 marking configuration 1) 2) part no. F1G56 rev. date 2007-07-13 i t f co., ltd. 102-901, bucheon technopark 364, samjeong-dong, ojeong-gu, bucheon-city, gyounggi-do, korea 421-809 rev. nc7001-as02 3/7 l q 3) 1) index mark 2) part number mark 3) lot number ( itf standard rule ) * ink or laser marking available
saw bandpass filter F1G56 typical performance ( at 25 ) ch1 s21 log 10 db/ ref 0 db center 1 575 . 420 000 mhz span 300 . 000 000 mhz cor 12 mar 2007 15:27:56 1 2 3 4 5 5: -1 . 1804 db 1 574 . 420 000 mhz ch1 markers 1: -36 . 901 db 1. 50000 ghz 2: -1 . 1804 db 1. 57442 ghz 3: -1 . 0502 db 1. 57642 ghz 4: -29 . 835 db 1. 62500 ghz ch1 s21 log 10 db/ ref 0 db start . 010 000 mhz stop 3 000 . 000 000 mhz cor 12 mar 2007 15:32:51 1 2 3 2: -1 . 0745 db 1 575 . 420 000 mhz ch1 markers 1: -36 . 735 db 1. 50000 ghz 3: -29 . 669 db 1. 62500 ghz part no. F1G56 rev. date 2007-07-13 i t f co., ltd. 102-901, bucheon technopark 364, samjeong-dong, ojeong-gu, bucheon-city, gyounggi-do, korea 421-809 rev. nc7001-as02 4/7
saw bandpass filter F1G56 input / output vswr charts ch1 s11 swr 1 / ref 1 center 1 575 . 420 000 mhz span 300 . 000 000 mhz cor 12 mar 2007 15:29:13 1 2 3 3: 1. 1273 1 575 . 420 000 mhz ch1 markers 1: 1. 1697 1. 57442 ghz 2: 1. 1106 1. 57642 ghz ch1 s22 swr 1 / ref 1 center 1 575 . 420 000 mhz span 300 . 000 000 mhz cor 12 mar 2007 15:29:29 1 2 3 3: 1. 0959 1 575 . 420 000 mhz ch1 markers 1: 1. 1367 1. 57442 ghz 2: 1. 0761 1. 57642 ghz input / output smith charts ch1 s11 1 u fs center 1 575 . 420 000 mhz span 300 . 000 000 mhz cor 12 mar 2007 15:29:02 1 2 3 3: 53. 186 5. 3164 537 . 08 ph 1 575 . 420 000 mhz ch1 markers 1: 55. 193 6. 4141 1. 57442 ghz 2: 51. 916 5. 0117 1. 57642 ghz ch1 s22 1 u fs center 1 575 . 420 000 mhz span 300 . 000 000 mhz cor 12 mar 2007 15:29:21 1 2 3 3: 52. 459 3. 9980 403 . 90 ph 1 575 . 420 000 mhz ch1 markers 1: 54. 260 5. 1270 1. 57442 ghz 2: 51. 324 3. 4551 1. 57642 ghz part no. F1G56 rev. date 2007-07-13 i t f co., ltd. 102-901, bucheon technopark 364, samjeong-dong, ojeong-gu, bucheon-city, gyounggi-do, korea 421-809 rev. nc7001-as02 5/7
saw bandpass filter F1G56 packing specification 1. reeling quantity : 3000 pcs / 13? reel ( or 1000 pcs / 7? reel ) 2. taping structure : the tape shall be wound aroun d the reel in the direction shown below. reel top cover tape carrier tape tape specification 1. leader part and vacant position specification end start tape running direction vacant 150mm min. component contained vacant 150mm min. leader part 250mm min. 2. tensile strength of carrier tape 4.4n/mm width 0~15 degree top cover tape direction of pull carrier tape 3. top cover tape adhesion 1) pull off angle : 0~15 2) speed : 300mm/min 3) force : 20~70g part no. F1G56 rev. date 2007-07-13 i t f co., ltd. 102-901, bucheon technopark 364, samjeong-dong, ojeong-gu, bucheon-city, gyounggi-do, korea 421-809 rev. nc7001-as02 6/7
saw bandpass filter F1G56 carrier tape dimensions [unit : mm] top cover tape part direction tape running direction reel dimensions [unit : mm] part no. F1G56 rev. date 2007-07-13 i t f co., ltd. 102-901, bucheon technopark 364, samjeong-dong, ojeong-gu, bucheon-city, gyounggi-do, korea 421-809 rev. nc7001-as02 7/7
|
